for Glass Lampworkers, Beadmakers, Flameworkers, Glassblowers and Marblemakers

• Surface Mix Tip works with all kinds of glass. Soft and Hard.
• Pre-Mix Mix Tips only work with Borosilicate Hard Glass (Pyrex) but is faster working.

Item #	Item	Price
16025	Burner - one bottom burner	$269
16026	Burner - with extra surface mix top torch mounted on top	$379
16027	Burner - with extra pre-mix top torch mounted on top - extra tips listed below	$379
1402	Torch Mounted Marvering Pad puts a graphite marvering pad in your work area close to the flame. Slightly tilted so pieces don't roll off. Edge can be used for shaping! ONLY for #16025	$24

Torch TIPS for the 16027

Single Orifice

Order #	Description	Hole size in inches	Price
OX-00	One Hole - Smallest size	.020	$19
OX-0	One Hole - Smallest size	.032	$17
OX-1	One Hole	.042	$15
OX-2	One Hole	.055	$12
OX-3	One Hole	.07	$12
OX-4	One Hole	.082	$12
OX-5	One Hole - Largest size	.1	$12

Thread size 7/16-24

---

Multiple Orifice

Order #	Description	Price
HTM-0	7 holes - each .04 inch diameter holes	$31
HTM-1	9 holes - each .04 inch diameter holes	$31
HTM-2	9 holes - each .048 inch diameter holes	$31
HTM-03	9 holes - each .055 inch diameter holes	$31

Order #	Description	Price
HTC-0	7 holes - Silent Burn	$30
HTC-1	12 holes - Silent Burn	$32
HTC-2	19 holes - Silent Burn	$37
HTC-3	31 holes - Silent Burn click here to see the HT3 tip fired up	$42

Thread size 7/16-24

Work Surfaces

Protect your work table

A comfortable pair of padded foam armrests and worksurface and rodrest all in one! All stainless steel. Pictured with a Minor Burner not included.

Glass Rod Rests This movable rod rest is used to support glass rods to keep them up off the flameworker's workbench for easier grabbing, better organization, and to keep the glass rods cleaner. The rippled edge keeps the rods from rolling around. These durable stainless steel rod holders can also be placed inside a glass bead kiln to support your mandrels. Made in the USA

Gas Regulators

Gas Hoses

Use this gas hose when you use a two gas torch (oxygen and propane) like a Minor Burner. Most torches are attached to the hose by pushing the cut end (no brass fitting) on to the torch and securing with a hose clamp. These hoses have two attached hoses, one for oxygen and one for propane. The end of the hoses are attached to the gas regulators. Propane hose fittings are always left handed threads and oxygen is right handed so there is never a mixup attaching hoses. The green hose is oxygen and propane is red. CAUTION Do not use the easy to find oxygen/acetylene type hoses. The propane gas will rot them. The hoses we sell are made for all types of gas including propane. All hose endings have brass fittings and are female. The fastest way to order any of these items is to call us toll free at 1-888-4HOTGLASS.

The below larger diameter hose is only used if when you need a large hose to fit over the large inlet fittings on some torches. (You can get the smaller 1/4" hose listed above on these large inlet fittings with a bit of effort. A trick is to emerse the end of the hose in very hot water to soften the end.)

Y - Connectors for Hose

Y Connector - Connect this fitting at the output of the regulator and attach two hoses so you can use two torches from the same tank. Oxygen and propane Y are packaged and priced separately.

Y Connector with valves - Same as the Y connector described above except has two on/off valves, one for each hose.

Order #	Description	Output end is a	Input end is a	Price
101	Y hose connector (oxygen)	hose (B fitting)	Oxygen regulator	$19.50
102	Y hose connector (propane)	hose (B fitting)	Propane regulator	$19.50
101V	Y hose connector with valve (Oxygen)	hose (B fitting)	Oxygen regulator	$32.50
102V	Y hose connector with valve (Propane)	hose (B fitting)	Propane regulator	$32.50

* The FA30 connects between the regulator and the gas hose and is more commonly used.

Flashback Arrestors

Flashback Arrestors - In some rare situations, a flame can travel back down a hose to the gas tank and cause an explosion. This device helps prevent this reverse gas flow and flashback. This device uses a reverse flow check valve and a flame arrestor that stops this flashback flame. Packaged and priced with both an oxygen and a propane arrestor.
A2 is optional, not included.

Order #	Description	Output end is a	Input end is a	List Price
FA10	Flashback arrestors (pair of oxygen and fuel gas) Connects directly to the fittings on a torch like the 3AB, 8M and Carlisle. We also include the fitting so you can put this arrestor in the middle of your twin hose. A good place to put this arrestor is a couple feet away from the torch. If you cut the hose you will not have fittings on the ends. Then must order one or two pair of A2 fittings for $5 to connect to arrestor.	Female B size hose fitting Male B size fitting using the included adaptor	Male B size hose fitting	$54
FA30	Flashback arrestors (pair of oxygen and fuel gas) Connects directly on the regulator.	male B size gas hose fitting	Female B size gas hose fitting	$54
A2	Insert into cut end of hose and secure with hose clamp. Check for leaks.	One side Female B size hose fitting	Other side a barb that fits in a 1/4" ID gas hose - use a hose clamp	$5
A30 ox A31 fuel	Oxygen and Fuel Gas Fittings - The pieces in the picture labeld "included". A pair of these are included in the FA10. If you need extra pieces order the A30 and A31 parts.	male B size gas hose fitting	male B size gas hose fitting	$1.50 each

Note: Flashback arrestors have an arrow stamped on it to indicate the gas flow direction. Works in only one direction.
* The FA30 connects between the regulator and the gas hose and is more commonly used. Requires B size fittings on hose.

Four Functions in a single item. Shorter and less expensive than if purchased separately.

Hose Quick Connects

Disconnect your torch easily and quickly for switching to a different torch or to put it away for safe keeping or great for quick classroom set up and take down.

Order #	Description	Input end is a	Output end is a	Price
QDB10	Quick Connects (pair)	Male B gas hose fitting	Female B fitting	$49
QDB20	Quick Connects (pair)	Hose to Hose	Hose to Hose	$49
QDB30	Quick Connects (pair)	Regulator	Male B hose fitting	$49

Manifold Gas System

Connect up to six torches to the same gas supply with this manifold system. Included are enough fittings and plugs to make 2 to 6 hose connections. Two manifolds are required, one for oxygen and one for propane. All Brass.

Custom Manifold Systems: We can help you figure out which parts you would need for your system and pre assemble for no extra charge. Systems might also include quick connects and flashback arrestors. Place an order.

Example Manifold setup for 3 torches.

---

Bulk Adaptor Systems

For users of Hot Head Torches or any torches similar to the HotHead torch. Save on the cost of propane by using a large bulk refillable propane tank instead of the small disposable fuel gas cylinders. Order No. F273701, uses a single hose with the correct fittings on each end. 5 or 12 foot hose.

Y-Propane F271735 Connect two torches with this fitting. This Y fits into a bulk tank - the two other ends fit two F273701 hoses which go to the Hot Head torches.

---

Spark Lighter

Use to light torches. Squeeze the handles together to cause a spark. Place an order.

		Retail
1501	Sparklighter Use to light torches. Squeeze the handles together to cause a spark.	$2